DX Engineering Antenna Accessories, ML&S Martin Lynch and Sons Ltd

DX Engineering Antenna Accessories

ML&S Store ¦ Accessories (By Manufacturer) ¦ DX Engineering Antenna Accessories

Product: DXE-UT-8213 (Coax Cable Stripper)

	This tool prepares RG-8, RG-213, 9913F7, LMR-400 (not LMR-400UF) and other similar size coax cable for installation of a PL-259 connector - or DXE-N1001S two-piece Type N connector (requires a slight additional trimming of the cable center conductor length). - How to use the DXE-UT-8213 Coaxial Cable Stripping Tool - Video - Coax Cable Stripping Tool Instructions Price (Inc VAT at 17.5%): £45.99 Ex-VAT Price: £39.14

Product: DXE-UT-80N (Connector Assembly Tool)

	This assembly tool* allows simple threading of the two-piece Type N connector sleeve onto the vinyl jacket of RG-8/U, RG-213/U, LMR-400 and other similar size cables. - How to use the DXE-UT-80N Type N Installation Tool - Video. - DXE-UT-80N Type N Installation Tool Price (Inc VAT at 17.5%): £25.96 Ex-VAT Price: £22.09

Product: DXE-UT-80P (Connector Assembly Tool)

	Originally introdruced as the DXE-UT-80TN at Hamvention® 2008, this assembly tool allows simple threading of PL-259 sleeve onto the vinyl jacket of RG-8/U, RG-213/U, LMR-400 and other similar size cables. - How to use the DXE-UT-80P PL-259 Installation Tool - Video. - PL-259 Installation Tool Instructions Price (Inc VAT at 17.5%): £25.96 Ex-VAT Price: £22.09

Product: DXE-363-SST
	This hi-quality bulkhead connector uses silver plated outer and inner conductors and a Teflon insulator. The connector has very low loss and high electrical break down. It comes with two nuts to secure the connector to our radial plate or other flat surface. Perfect for use with the DX Engineering Radial Plate, (DXE-RADP-1P) it ensures the radial ground system, the antenna ground and the feedline shield are common. It can also be used in other coaxial applications where the male ends (PL-259) of 2 coax cables need to be connected, such as when joining two pieces of coax together. Don't forget to waterproof coaxial connections. Price (Inc VAT at 17.5%): £7.15 Ex-VAT Price: £6.08

Product: DXE-AOK-17M

The DX Engineering DXE-AOK-17M kit adds 17 meter coverage to the Hustler BTV series of vertical antennas without giving up any existing band coverage. This kit will operate across the entire 17m band with an SWR of 1.5:1 or less.

No disassembly of the existing antenna is required, simply bolt this kit over the 10m trap, make some minimal tuning adjustments and you're on the air with an additional band.

People who bought this item also bought:

1. Icom MB-72

2. Icom BC-155A/D

3. Icom BP-228

Price (Inc VAT at 17.5%): £69.95
Ex-VAT Price: £59.53

Product: DXE-AOK-DCF

	The DXE-AOK-DCF Direct Coax Feed assembly by DX Engineering for the Hustler BTV series antennas allows direct connection from a coaxial cable with a PL-259 connector. Manufactured from heavy duty stainless steel, this add-on kit allows convenient connection from your coaxial cable feedline directly to the base of the Hustler BTV-series vertical antennas. It may be positioned in any one of three different directions to allow straight-in connection from your feedline. Price (Inc VAT at 17.5%): £22.95 Ex-VAT Price: £19.53

Product: DXE-ARAV-1P

The DX Engineering’s Active Receive Antenna system offers excellent receiving performance from 100 kHz to 30 MHz using a whip antenna element 102 in. long. DX Engineering’s unique design makes it vastly superior to traditional active antennas in both strong signal handling and feedline decoupling. You get significantly better weak signal reception due to lower spurious signal interference and reduced noise. This antenna system is ideal for Amateur Radio or Shortwave Listening.

This item is delivered in two boxes. The courier charge for this item is £20 (mainland UK, other areas may be different cost - you will be notified by e-mail if this is the case)

People who bought this item also bought:

1. Plug - PL-259

2. RG-213U Coax

3. MyDEL CG-3000

Price (Inc VAT at 17.5%): £259.95
Ex-VAT Price: £221.23

Product: DXE-BAL050-H10-A

	DX Engineering High Power Transmission Line Transformers and Baluns with Maxi-CoreTM Technology, allows your antenna perform to its full potential and reduces the stresses on your equipment. The DX Engineering DXE-BAL050-H10-A is a 1.8 - 30 MHz 1:1 High Power (5kW Continuous/10kW Peak) balun. Price (Inc VAT at 17.5%): £121.56 Ex-VAT Price: £103.45

Product: DXE-BAL050-H10-AT

	DX Engineering High Power Transmission Line Transformers and Baluns with Maxi-CoreTM Technology, allows your antenna perform to its full potential and reduces the stresses on your equipment. The DX Engineering DXE-BAL050-H10-AT is a 1.8 - 30 MHz 1:1 High Power (5kW Continuous/10kW Peak) balun built for use with an antenna tuner. Price (Inc VAT at 17.5%): £119.95 Ex-VAT Price: £102.08

Product: DXE-BAL050-H11-CT

	DX Engineering High Power Transmission Line Transformers and Baluns with Maxi-CoreTM Technology, allows your antenna perform to its full potential and reduces the stresses on your equipment. The DX Engineering DXE-BAL050-H11-CT is a 1.8 - 30 MHz 1:1 High Power (10kW Plus) balun built for use with an antenna tuner. Price (Inc VAT at 17.5%): £179.17 Ex-VAT Price: £152.48

Product: DXE-BAL200-H10-AT

	DX Engineering High Power Transmission Line Transformers and Baluns with Maxi-CoreTM Technology, allows your antenna perform to its full potential and reduces the stresses on your equipment. The DX Engineering DXE-BAL200-H10-AT is a 1.8 - 30 MHz 4:1 High Power (5kW Continuous/10kW Peak) balun. Price (Inc VAT at 17.5%): £153.57 Ex-VAT Price: £130.69

Product: DXE-BAL050-H10-CT

	DX Engineering High Power Transmission Line Transformers and Baluns with Maxi-CoreTM Technology, allows your antenna perform to its full potential and reduces the stresses on your equipment. The DX Engineering DXE-BAL200-H10-CT is a 1.8 - 30 MHz 4:1 High Power (10kW Plus) balun built for use with an antenna tuner. Price (Inc VAT at 17.5%): £179.17 Ex-VAT Price: £152.48

Product: DXE-BDAB-1P

This mounting kit allows you to mount a DX Engineering Balun, Feed Line Current Choke, or Vertical Feedline Current Choke in a wire dipole situation.

Kit includes:
- Polymer Dipole mounting bracket
- Stainless steel mounting hardware

People who bought this item also bought:

1. DXE-VFCC-H05-A

2. DXE-TB-3P

Price (Inc VAT at 17.5%): £10.17
Ex-VAT Price: £8.65

Product: DXE-BMB-2P

	This handy Aluminum mounting bar and Stainless Steel hardware kit will allow you to mount your quality DX Engineering Balun, Feed Line Current Choke, or Vertical Feedline Current Choke, directly to a 1.56 in. thru 2.25 in. boom. Works with any DX Engineering Formed Aluminum Enclosure Kits includes: - 1x - Mounting Bracket - 1x - Bracket Hardware Kit - 2x - Boom Clamps Price (Inc VAT at 17.5%): £16.02 Ex-VAT Price: £13.63

Product: DXE-CAVS-1P

	This V-Clamp is made in one size that fits tubing from 1/2 to 1-3/4'' O.D. as used in antenna construction. The supplied V-bolt is long enough to attach tubing to thick plates and is made with anti-corrosive properties. The as-cast rippled surface of the saddle will clamp the tubing securely to a flat surface. Price (Inc VAT at 17.5%): £14.56 Ex-VAT Price: £12.39

Product: DXE-CSB-COMBO

	Ferrite Beads in a Split Carrier, Combo Pack - Assorted Pack of 8. - Reduce or eliminate ignition/injector noise - 3 S-units improvement not uncommon! - Hear many more stations - 31-mix is optimal for HF - Snaps on - no cutting - Mobile or home use - any RFI application Price (Inc VAT at 17.5%): £52.60 Ex-VAT Price: £44.76

Product: DXE-EGK-200

	The DX Engineering DXE-EGK-200 is a 2" Grounding Exhaust Kit. Price (Inc VAT at 17.5%): £18.88 Ex-VAT Price: £16.06

Product: DXE-FCC050-H05-A

	The DXE-FCC050-H05-A Feedline Current Choke, using Maxi-Core® technology, prevents unwanted RFI by eliminating feedline current and radiation in 50 Ohm, coaxially fed antenna systems. It provides excellent feedline decoupling and low loss performance from 1 to 60 MHz and is power rated for 2 kW continuous, 5 kW intermittent. The FCC has significantly higher common mode impedance and a larger effective core area than similar line isolators, including conventional enameled wire or bead baluns. Price (Inc VAT at 17.5%): £99.95 Ex-VAT Price: £85.06

Product: DXE-HR-1P

	The DX Engineering Hot Rodz™ is an adjustable capacity hat system that increases the efficiency and gain of single-band vertical antennas, such as those from Hustler and Pro Am. Hot Rodz can even shorten the height of the antenna by eliminating the need for a whip. Hot Rodz can also be used on the Hustler 4, 5 and 6-BTV Series antennas by experienced antenna practitioners. Price (Inc VAT at 17.5%): £54.63 Ex-VAT Price: £46.49

Product: DXE-MM-1

	The MM-1 is a dual ratio UN-UN (unbalanced to unbalanced transformer). Great for coupling your 50 Ohm coax to an antenna with a feed point impedance of either 25 or 12.5 Ohms, typically found in a mobile environment. Price (Inc VAT at 17.5%): £109.67 Ex-VAT Price: £93.33

Product: DXE-RADP-1HWK

	Additional 20 Sets of ALL Stainless Steel Radial Hardware for use with the DX Engineering Stainless Steel Radial Plate. (20) 1/4'' Bolts (20) 1/4'' Nuts (20) 1/4'' Flat Washers (20) 1/4'' Split Washers (20) 1/4'' Star Washers Price (Inc VAT at 17.5%): £7.67 Ex-VAT Price: £6.52

Product: DXE-RADP-1P

The DXE-RADP-1P is a Plate, Stainless Steel w/ 20 Sets of SS Radial Attachment Hardware.

The DX Engineering Radial Plate is meant for those of you that have or are building a quarter wave vertical antenna and who want an easy, neat and effective way to connect those essential radial wires and the coax to your vertical antenna for the lowest takeoff angle and strongest signals.

This plate will work perfectly with most commercially available vertical antennas such as the Hustler BTV series (4BTV thru the 6BTV), the SteppIR (BiggIR or SmallIR) or one of your own construction.

People who bought this item also bought:

1. Snap Hook 8 x 80mm - BE923/80

2. Alpha Delta CIN

3. 9" Wall Bracket - BE715/09

Price (Inc VAT at 17.5%): £59.95
Ex-VAT Price: £51.02

Product: DXE-RADW-500KBD

	To achieve optimal performance with a ground-mounted vertical, install as many radials as possible. This bulk radial wire kit uses insulated wire that is UV resistant, hard to see and lays down easily, unlike the wire that is commonly available at the big box stores. It will last much longer in contact with soil than bare wire. The biodegradable anchors allow easy installation of radial wires, and will degrade and disappear in a year or so when they are no longer needed - environmentally friendly! Price (Inc VAT at 17.5%): £61.30 Ex-VAT Price: £52.17

Product: DXE-RR8-HP-P

	The DXE-RR8-HP is the smallest antenna switch in the DX Engineering RR8 series. It is designed to switch up to 8 coaxial lines in low to medium power RF systems. Sealed relays provide exceptional performance and are moisture resistant. The RR8-HP can be configured to simultaneously select multiple output ports as well as conventional one-of-eight antenna switching. This allows the RR8-HP to be used in complex antenna phasing and stacking systems as well as traditional switching arrangements. Price (Inc VAT at 17.5%): £329.96 Ex-VAT Price: £280.81

Product: DXE-SAD-200A

	These Saddle Clamps are made in sizes that fit thick wall tubing, used in antenna construction not like clamps found at your typical automotive sources. The supplied U-bolt is long enough to attach tubing to thick plates and is made with anti-corrosive properties and will grip securely to the tubing. U-Bolt thread dimensions: 5/16"-18 x 1.12 Price (Inc VAT at 17.5%): £13.61 Ex-VAT Price: £11.58

Product: DXE-STPL-100BD

	DX Engineering DXE-STPL-100BD is a 100-pack of 3” biodegradable anchors that are produced from recycled PLA (Polylactide Resin). Depending on the weather conditions, they will degrade in about a year. They are easily installed and will hold radial wires in place until lawn roots overtake them - and then disappear. Ecologically friendly! They don't slowly rust away like metal staples. These staples are intended for softer ground where they may be pushed in - or lightly tapped with a tool head. Since they are a plastic material, they will be subject to breakage in rocky or hard soil. They are not intended to be "hammered" in. For that type of application, we still offer the DXE-STPL-100P (pk of 100) and DXE-STPL-300P (pk of 300) Steel Wire Staples. Price (Inc VAT at 17.5%): £16.34 Ex-VAT Price: £13.90

Product: DXE-TB-3P

The DX Engineering DXE-TB-3P is a Tilt Base Kit for 1/4 wave Hustler 4, 5 & 6 BTV Verticals.

With a DX Engineering Tilt Base, operators can raise or lower their BTV vertical in seconds while leaving the base plate securely attached to the mounting pipe or post. One person can service the antenna—no more climbing ladders or removing brackets.

People who bought this item also bought:

1. DXE-BDAB-1P

2. DXE-VFCC-H05-A

Price (Inc VAT at 17.5%): £64.95
Ex-VAT Price: £55.27

Product: DXE-VFCC-H05-A

The DX Engineering DXE-VFCC-H05-A is a 2/5 kW Vertical Feedline Current Choke.

If your antenna SWR is already low and you wish to reduce feedline radiation and improve reception, a Feedline Current Choke is recommended. Adding a DX Engineering Feedline Current Choke at the base of a vertical antenna will substantially reduce unwanted feedline radiation (RFI), reducing the need for improved station grounding.

People who bought this item also bought:

1. DXE-BDAB-1P

2. DXE-TB-3P

Price (Inc VAT at 17.5%): £121.56
Ex-VAT Price: £103.45

This website is best viewed in Internet Explorer 8, you are able to download it here. Best viewed in 1024x768 or above screen resolution.
Terms & Conditions | Privacy Statement | Online Security | Site Map | Contact

We Accept These Credit Cards
Shopping online at ML&S is safe & secure. More info

Martin Lynch & Sons Ltd . Outline House . 73 Guildford Street . Chertsey . Surrey . KT16 9AS
Opening Hours: Monday to Friday - 9:00 to 5:30, Saturday - 9:30 to 5:00 Tel: +44 (0)845 2300 599 Fax: +44 (0) 1932 567 222 Email: